Scope: Maximum pressure is higher than 0.5 bar pressure equipment and components. "Pressure Equipment" means vessels, piping, and security components and pressure parts. No ranges: Non application of pressure equipment 3.1 is designed for any flow or material to transport or offshore or onshore facility by a proceeding by the pipeline pipeline system consisting of pipelines, including the facility located facilities within the last insulation and all the expertise for Additional equipment and piping design to them as a starting point of the pipeline. But this does not include such pressure in the decompression station or stations can see the standard pressure equipment; 3.2, such as pressure pipe, pressure tunnels, hydropower strut shaft and a class of special equipment related to the supply, distribution and excretion of water pipeline network and related equipment and flume; 3.3 of 87/404/EEC on simple pressure vessels Directive within the scope of the standard equipment; 3.4 for the coordination of Member States in the legislation on smoke dispersal devices in May 20, 1975 promulgated by the EC Council directives 75/324/EEC involved in standard setting; 3.5 standard and its appendices by the following command as a means of delivery specified in the device: - EU Council on 6 February 1970 announced the implementation of the coordination of Member States in the power car and trailer type approval legislation on the instructions of the standard 70/156/EEC (11). - EU Council on May 4, 1974 announced the implementation of the coordination of Member States in the agricultural and forestry wheeled tractors with model legislation approved by the instructions on the standard 74/150/EEC (12). - EU Council on June 30, 1992 promulgated on two or three power command vehicle type approval standards 92/61/EEC (13); 3.6 According to Article 9 of the Directive standards are classified in Class I is not higher than the standard equipment and is one of the following commands: - By the European Council on June 14, 1989 announced the implementation of the machinery for the coordination of Member States of the Council Directive on the legislative standard 89/392/EEC (14), - by the European Parliament and the Council on June 29, 1995 announced the implementation of the coordination of Member States in the elevator on the legislative directive standards 95/16/EC (15), - By the European Council on 19 February 1973 announced the implementation of the coordination of Member States in a voltage range in the design of electrical equipment used within the legislative directives on standards 73/23/EEC (16), - EU Council on June 14, 1993, promulgation and implementation of standards on medical devices directive 93/42/EEC (17), - EU Council on June 29, 1990 announced the implementation of the coordination of Member States in the combustion gas equipment standards on the legislative directive 90/396/EEC (18), - European Parliament and EU Council on March 23, 1994 announced the implementation of the coordination of Member States in the conditions used in explosive gas equipment and protection systems under the legislation of the directives on standard 94/9/EC ( 19); 3.7 Treaty Article 223 (1) (b) of the equipment involved: 3.8 dedicated to the use of nuclear devices that can cause failure of the nuclear radiation leak; 3.9 for oil, gas, geological exploration and mining industry and underground mining, which are required to control well pressure and well control equipment; including the well source wellhead (Christmas tree), blowout preventer (BOP), and all its manifold The high equipment; 3.10 including those casing and mechanical equipment, their size and material should be selected depending on production requirements and to meet them for the static or dynamic operating results or other operating performance requirements necessary strength, rigidity and stability , in the design pressure is not a very important factors to consider, these devices are: - including turbines and internal combustion engine; - steam engines, gas turbines, turbo generators, compressors, pumps and starting device; 3.11 including the blast furnace cooling systems, waste heat recovery boiler and dust collector for blast furnace and blast furnace gas dust; including blast furnace cooling, gas absorption converter melting, then melting, degassing and casting non-ferrous metal ingots and the direct reduction furnace; 3.12, such as power distribution equipment, control devices, transformer and high voltage electrical rotating machinery and other equipment box cover; 3.13 Built-such as power and telephone lines, the pressure transmitter system piping; 3.14 ships, rockets, aircraft, offshore and specialized mobile device or on board aircraft or propulsion systems on their equipment; 3.15 by words such as tires, air, inflatable ball, air pressure equipment, craft and other similar body composition of soft inflatable pressure devices; 3.16 deflated air intake silencer 3.17 users direct consumption of beverage bottles or cans of carbon; 3.18 is not greater than 500 bar pressure PSTV 7L and maximum allowable pressure not higher than 7 bar for transport and distribution of beverage containers; 3.19 With regard to the road transport of dangerous goods in the relevant provisions of the Europe Agreement (ARD20), transport of dangerous goods on railway wagon regulations (RID21), the International Maritime Dangerous Goods Transportation Act (ZMDG22) and ICAO, the equipment required by Agreement ; 3.20 Hot water radiator heating system and pipes; 3.21 Design for holding liquid surface pressure is not greater than 0.5 bar pressure of the liquid container.